Smartdate 5 manual

Controller — Multiple user interface options including color touch screen and web pages. Dedicated buttons for frequently used functions. USB for image and file data transport. Equipped with power save mode. Print Area —. Markem Smartdate 5 intermittent thermal transfer printer system. Prints up to a 53 mm x 75 mm 2. Includes print head, ribbon cassette, touch screen, user interface, cables, air regulator, us- er's manual, and mounting bracket.

Jan 23, Publication Number: OM Revision Level: 5. Revision Date: March Firmware Version: 3. Proprietary Notice.

Information in this document is subject to change without notice and does not represent Throughout this manual, trademarked names may be used. Page Company History. Encoder Products Company Inc. EPC is a leading designer and world-wide manufacturer of motion sensing devices. Founded in by William Watt,. EPC began operations with a small line of custom encoders. User Manual. August International Ltd. The speed profile once initiated records speed samples.

A low resolution ms will record over a longer period. Shuttle printer - DRS mode - This section is designed to provide information about how to keep your SmartDate 5 in good working order. Particular attention should be given to the inside of the printer body, especially if food products are able to fall into the unit. Imaje SmartDate 5 technology for package identification. Pull the ribbon through by hand, and visually check to see if the ribbon is creasing across the width of the ribbon.

Replace if necessary. Careful consideration at the time of installation and regular preventative maintenance can significantly help to maximise printhead life. The most frequent cause of printhead damage is abrasion - either from ingress of airborne particles or from an abrasive substrate surface. These depend on machine use, operating environment, and choice of thermal ribbon. Turn off the power to the controller and remove the ribbon cassette.

Allow the printhead to cool to normal room temperature before proceeding in order to prevent the possibility of thermal shock damage. Turn off the power to the controller and isolate the air supply to the printer body. Remove the ribbon cassette. Always ensure anti static precautions are used when handling new printheads. Connect the printhead cable to a 6. Push the printhead forwards in the replacement printhead.

Swing the back of printhead inwards, this allows it to be secured into the print module. This value must be entered into the controller menu structure. The processor will then adjust the voltage level to suit the particular printhead resistance level. Menu File Management Printhead Resistance Press the right button to Select the menu. The Printhead Resistance menu screen is displayed. Remove the retaining screw from 2. Remove the screw and washer and the end of Peel roller. If the peel roller shaft has been 6.

Fit a new peel roller assembly damaged, undo the retaining nut at and ensure that the retaining nut is the base and remove the complete secure. The procedure is as follows: 2. Before fitting a replacement roller, 1. The procedure is as follows: 1. Remove the securing screw on 2. Remove the damaged roller by 2.

Before fitting a replacement roller, applying a spanner to the two flat apply Loctite to the screw thread surfaces at the base of the roller. Remove the cover from the 2. Remove the retaining screw printer body and disconnect the from the printer base plate. Dependant on the hand of the cassette the ribbon supply flange red may have to be removed to gain access to the securing screws.

Remove the sensor retaining screws 1. Remove the cover from the printer from the printer base plate. Remove the micro switch printer body and disconnect the retaining screws from the printer appropriate micro switch connector. Remove the cover from the printer 2. Disconnect the air pipes from the body and disconnect the PCB appropriate valve. The belt should be checked at regular intervals for wear or damage.

If the belt has to be replaced, the procedure is as follows: 3. Remove the belt clamp and re-fit it 5. Remove the damaged drive belt. Fit the new belt onto the printer. Refit the Drive belt clamp. Position and re-secure the print 9. Remove the four retaining screws 1. Remove the two retaining screws from the print module. Remove the three retaining screws 3. Remove the printhead module 6.

Loosen off the belt tensioner adapter plate, and place to the side. Remove the shuttle carriage and 7. Remove the securing screws from damaged drive belt. Remove the belt clamp and re-fit it Fit a new belt to the printer and re- to the new belt.

Adjust the belt tensioner, allowing Secure the Shuttle carriage approximately 4 mm of movement on screws. Re-fit and secure the print module Position and re-secure the print adaptor plate.

Be sure to respect the publishers and the authors office file copyright. Toggle navigation pdf Book free download. If all the pins are aligned correctly, push the board all the way into the socket.

Turn the board Windows Server " certification for and bit systems. Back to Top Markem-Imaje SmartDate 5 mm Continuous. Dual-Laser Omnidirectional Scanner.

Verify the Scanning Operation. Before installing your scanner, please follow the procedures below. This will lead to proceed for scanning properly. Connect the modular plug of the power link cable into the back of the scanner. Plug the DC plug of the power Installation and Configuration Guide. The Smart Card solution brings an advanced level of security to sensitive information. This ensures only authorized users are able to copy, scan, e-mail and fax information.

Once validated, a Guides v8. Quick Start Guide and Administrator's guide are now directly accessible from the Help menu. Label Background with image v8. A new Extended tab in Nov 30, Use the flow detail page to do anything with your flow outside of designing it— such as activating a flow, testing it, or viewing its The transaction doesn't retry any of the operations—including the flow interview.

Limits for Visual Workflow.